CCS - CCS4 Mooring data May 2019 deployment

Project Overview: A range of solutions will be required to reach globally agreed emissions reductions targets for carbon dioxide (CO2). Carbon capture and storage (CCS) is part of the suite of technologies that will contribute to lowering atmospheric emissions of CO2 from Australia's energy system. There are a wide variety of technologies at various stages of technical and commercial readiness, with more development underway for cost effective CO2 capture and storage. Our research will provide new knowledge to inform cost-efficient measurement, monitoring and verification (MMV) of the environment of CCS projects in coastal waters.\n\n--o--\n\nDescription:\n\nMeasurements are made Seabird Seaphox (for dissolved oxygen, pH, Seawater Temperature and Salinity), mounted on a lander. The Seaphox takes a reading every hour in the UTC hour and is transmitted real time through acoustic and/or 3G modems. The Seaphox consists of a SeaFET (pH) and SBE-37-SMP-ODO CTD (SW temperature, Salinity and Dissolved Oxygen [SBE63]).\n\nRelevant component details: make, model, serial number, firmware version, settings:\n\nSensor | Make | Model | Serial Number | Calibration\n\npH, DO,T and S sensor | Seabird Seaphox | SeaFET | 1001 | 2017-05, factory calibrated, verified by CSIRO lab\n\npH, DO,T and S sensor | Seabird Seaphox | SBE-37-SMP-ODO | 15560 | 2017-05, factory calibrated, verified by CSIRO lab\n\npH, DO,T and S sensor | Seabird Seaphox | SBE-63 | 1690 | 2017-05, factory calibrated, verified by CSIRO lab\n\nCalibration Information (if applicable)\n\nSBE 37 (T, S, DO) and the SeaFET (pH) are calibrated by the factory and verified in the CSIRO laboratory. The pH reported in the files is flagged questionable for the pre-deployment calibrated data due to possible calibration changes which can occur after deployment\n\npH (calibrated) is further processed after the recovery using in situ bottle sample where available, using Total Alkalinity (TA) and Dissolved Inorganic Carbon (DIC), which will be converted to pH using CO2SYS, where the Lueker k1k2 dissociation constant is used.\n\nLocation: 38.2564S 147.4162E项目概述：要实现全球共识的二氧化碳（CO₂）减排目标，需依托一系列解决方案。碳捕获与封存（CCS, Carbon Capture and Storage）是助力降低澳大利亚能源系统向大气排放CO₂的技术谱系中的一环。当前已有多种处于不同技术与商业化成熟度阶段的相关技术，且针对低成本高效的CO₂捕获与封存技术仍在推进更多研发工作。本研究将提供全新认知，为近岸海域CCS项目的环境成本效益型测量、监测与验证（MMV, Measurement, Monitoring and Verification）工作提供决策参考依据。 --o-- 数据采集说明：搭载于着陆器的Seabird Seaphox传感器（用于测量溶解氧、pH值、海水温度与盐度）开展现场测量。该传感器于每小时UTC整点采集一次数据，并通过声学调制解调器和/或3G调制解调器实时传输采集结果。Seaphox传感器集成了SeaFET（pH传感器）与SBE-37-SMP-ODO CTD（用于测量海水温度、盐度与溶解氧的SBE63模块）。 相关组件详情：品牌、型号、序列号、固件版本与参数设置： | 传感器类型 | 品牌 | 型号 | 序列号 | 校准信息 | | --- | --- | --- | --- | --- | | pH、溶解氧、温度与盐度传感器 | Seabird Seaphox | SeaFET | 1001 | 2017年5月工厂校准，经CSIRO实验室验证 | | pH、溶解氧、温度与盐度传感器 | Seabird Seaphox | SBE-37-SMP-ODO | 15560 | 2017年5月工厂校准，经CSIRO实验室验证 | | pH、溶解氧、温度与盐度传感器 | Seabird Seaphox | SBE-63 | 1690 | 2017年5月工厂校准，经CSIRO实验室验证 | 校准信息（如适用）： SBE 37（温度、盐度、溶解氧）与SeaFET（pH传感器）均经原厂校准，并在CSIRO实验室完成复测验证。文件中记录的pH数据在部署前校准阶段被标记为可疑，原因是部署后可能发生校准偏移。 经校准的pH数据需在回收后结合现场原位水样（若有）开展进一步处理，通过总碱度（TA）与溶解无机碳（DIC）数据，结合CO2SYS软件与Lueker型k1k2解离常数公式计算得到最终pH值。 采集位置：南纬38.2564°，东经147.4162°