遇见数据集

Welding sound database for benchmark metal transfer modes in gas metal arc welding

收藏
Mendeley Data2024-03-27 更新2024-06-28 收录
官方服务:

资源简介:

This database contains the synchronized sound, current and voltage signals measured at different benchmark transfer modes in gas metal arc welding. The benchmark metal transfer modes include three groups, i.e., contact, free flight and controlled. In each group, there are four modes. In Group 1 (contact transfer), the four modes are pure liquid bridge (1b2), forced contact (1c3), repel globular (1g4) and gasless explosive (1e10). In Group 2 (free flight transfer), the four modes are repel globular (2g4), forces spray (2s2), pure stream (2t2) and gasless explosive (2e10). In Group 3 (controlled transfer), the four modes are pure contact (3c2), forced pulse (3p3), projected spray (3s7) and gasless explosive (3e10). Four samples were welded at each mode, hence there are a total of 3 (group) × 4 (modes in each group) × 4 (sample for each mode) = 48 samples in the database. In the experiments, a Lincoln Electric PowerWave C300 welder was used with the torch being positive and the negative cable being connected to the workbench. During welding, the torch was fixed and the workbench was moving at a travel speed that was controlled by a servo motor. A GRAS 40PH free field microphone was hanged 0.6 m above the weld pool to record the welding sound. The microphone was connected to an NI 9234 Sound and Vibration module. An LEM HTA 300-S current sensor was installed around the torch cable to measure the welding current through the torch. The current sensor was connected to an NI 9215 Analogue Voltage Input module. Both the NI 9234 and NI 9215 modules were installed in an NI cDAQ 9185 chassis, which was connected to a desktop computer. The computer and the data acquisition system was in the black cabinet on the right of the photo in Fig. 6 and therefore is not shown here. A software with a user interface was developed with LabWindows/CVI 2017 to acquire, display and store the signals in synchronisation. The sampling rate for the sound and current/voltage signals are 51.2 kHz and 3.2 kHz, respectively. In the experiments, the pure argon was used as the shielding gas and the diameter of the feeding wire was 0.9 mm. The workpiece metal was carbon steel.

本数据集包含气保金属电弧焊(gas metal arc welding)不同典型熔滴过渡模式下采集的同步声信号、电流信号与电压信号。典型熔滴过渡模式共分为三大类,即接触过渡、自由飞过渡与受控过渡,每一类下均包含4种过渡模式: 1. 第1类(接触过渡):纯液桥过渡(1b2)、强制接触过渡(1c3)、排斥球状过渡(1g4)与无气爆炸过渡(1e10); 2. 第2类(自由飞过渡):排斥球状过渡(2g4)、强制喷射过渡(2s2)、纯射流过渡(2t2)与无气爆炸过渡(2e10); 3. 第3类(受控过渡):纯接触过渡(3c2)、强制脉冲过渡(3p3)、投影喷射过渡(3s7)与无气爆炸过渡(3e10)。 每种过渡模式下均完成4组焊接试样采集,因此本数据集共计3(类别数)×4(每类模式数)×4(每模式试样数)=48组样本。 本实验采用林肯电气(Lincoln Electric)PowerWave C300型焊机,焊枪接正极,负极电缆连接至工作台。焊接过程中焊枪固定不动,工作台由伺服电机控制以设定焊接速度移动。采用GRAS 40PH型自由场麦克风(安装于熔池上方0.6m处)采集焊接声信号,麦克风连接至NI 9234型声振采集模块;在焊枪电缆外侧安装LEM HTA 300-S型电流传感器,以采集流经焊枪的焊接电流,该传感器连接至NI 9215型模拟电压输入模块。NI 9234与NI 9215模块均安装于NI cDAQ 9185型机箱内,该机箱与台式计算机相连。台式计算机与数据采集系统均放置于图6照片右侧的黑色机柜内,因此未在本图中展示。本研究采用LabWindows/CVI 2017开发了带用户交互界面的采集软件,实现信号的同步采集、实时显示与存储。声信号与电流/电压信号的采样率分别为51.2 kHz与3.2 kHz。本实验采用纯氩气作为保护气,焊丝直径为0.9mm,工件材料为碳钢。

创建时间:
2023-06-28
搜集汇总
背景与挑战
背景概述
该数据集是一个气体金属弧焊中金属转移模式的焊接声音数据库,包含同步采集的声音、电流和电压信号,覆盖接触、自由飞行和受控三类基准转移模式,共12种具体模式,总计48个样本。数据集采用标准化实验设置,包括特定焊机、麦克风和数据采集系统,采样率分别为51.2 kHz(声音)和3.2 kHz(电流/电压),适用于焊接过程监测和模式识别研究。
以上内容由遇见数据集搜集并总结生成
二维码
社区交流群
二维码
科研交流群
商业服务