Numerical Fire Spread Simulation Based on Material Pyrolysis - An Application to the CHRISTIFIRE Phase 1 Horizontal Cable Tray Tests - Data Set

This data set is a supplementary resource for the article "Numerical Fire Spread Simulation Based on Material Pyrolysis - An Application to the CHRISTIFIRE Phase 1 Horizontal Cable Tray Tests", published by the peer-reviewed open access journal Fire. It is part of the "Fire Propagation in Cable Tray Installations" project. The provided data is only a summary of the full data produced for the article, due to its size. This article was previously submitted to the Fire Safety Journal and got eventually rejected. The information is structured into multiple *.rar archieves, which mimic the sub-directory structure created for the work. To be able to run the analysis scripts without much tweaking, extract all archieves into the same directory, with each archieve being a sub-directory in it. The data set is comprised of: The PROPTI and FDS input files used for the inverse modelling process (IMP) -- the 13* archieves. Full FDS simulation data of the mirco-combustion calorimeter (MCC) simulations of the best parameter sets per generation of the IMP runs, for jacket and insulator materials. Full FDS simulation data of the Cone Calorimeter simulations of the best parameter sets per generation of the IMP runs, for all three (25 kW/m², 50 kW/m², 75 kW/m²) incident heat flux conditions. FDS input files for the MT3 simulations, but full data only for the best parameter sets per IMP run (see below). Jupyter notebooks used for the analysis of the simulation responses including the scripts and plots generated for, and used in, the paper (RunReports). A general information directory, containing the FDS input file templates, experimental data used as target and Python scripts containing helper functions. Videos of a qualitative comparison of the SmokeView animation of the best parameter set in a cable tray simulation against a video from the experiment and an animation of the GAUGE_HEAT_FLUX development for the same simulation over the course of the simulation. Due to the size of the MT3 simulation data, only the FDS input files for the best parameter sets per generation are uploaded. Complete FDS simulation data is only provieded for the best perameter set of each IMP run, these are : IMP run, best rep. -------------------------------- imp_13b, 110751 imp_13c, 121106 imp_13d, 137738 imp_13e, 97493 imp_13f, 91988 imp_13g, 86988 imp_13h, 17480 imp_13b_1, 19033 imp_13b_2, 25043 imp_13b_3b, 24149 imp_13b_4, 29666 imp_13h_1, 10685 imp_13h_2, 10024 imp_13h_3, 10109 imp_13i, 13253 Note: The individual runs of the IMP are named differently as compared to the labeling used in the paper, as described below: IMP run, label in paper -------------------------------- imp_13b, Tb imp_13c, Ta imp_13d, Tc imp_13e, Ta,b,c imp_13f, Tb,c imp_13g, Ta,c imp_13h, Ta,b,cLA,L1,HC imp_13b_1, TbL1 imp_13b_2, TbPL1 imp_13b_3b, TbPL1L1 imp_13b_4, TbPL2,HT imp_13h_1, Ta,b,cPA,L1,HCL1 imp_13h_2, Ta,b,cPA,L1,HCL2 imp_13h_3, Ta,b,cPA,L1,HCL3 imp_13i, TbPA,L1,HC Version 2 changes: Added pre-print. Version 3 changes: Added new files that where produced during the revision process, after the original manuscript got rejected by the Fire Safety Journal. This revision corresponds to the intitial manuscript that was submitted to the journal Fire. The respective Zip archieves are labeled with a "_Revision01".本数据集为发表于同行评议开放获取期刊《Fire》的论文《基于材料热解的火灾蔓延数值模拟——在CHRISTIFIRE第一阶段水平电缆托盘试验中的应用》的补充资源，隶属于"电缆托盘安装中的火灾蔓延"项目。由于完整数据体量较大，本次仅提供该论文所用全部数据的摘要版本。该论文此前曾投稿至《Fire Safety Journal》并最终被拒。 本数据集的所有数据以多个*.rar压缩包进行组织，其目录结构与本研究构建的子目录结构一致。为确保分析脚本可无需大量修改即可正常运行，请将所有压缩包解压至同一目录下，每个压缩包对应其中一个子目录。 本数据集包含以下内容： 1. 用于逆向建模（IMP, Inverse Modelling Process）过程的PROPTI与FDS（Fire Dynamics Simulator）输入文件，共13个压缩包。 2. 针对护套与绝缘材料，各代逆向建模运行所得最优参数集的微燃烧量热仪（MCC, Micro Combustion Calorimeter）模拟完整FDS仿真数据。 3. 针对三种入射热流密度条件（25 kW/m²、50 kW/m²、75 kW/m²），各代逆向建模运行所得最优参数集的锥形量热仪模拟完整FDS仿真数据。 4. 用于MT3模拟的FDS输入文件，仅上传各逆向建模运行所得最优参数集的完整数据（详见下文）。 5. 用于仿真结果分析的Jupyter Notebook，包含为本论文生成并使用的脚本与绘图文件（即RunReports）。 6. 通用信息目录，内含FDS输入文件模板、用作目标值的实验数据，以及包含辅助函数的Python脚本。 7. 两段视频：其一为电缆托盘仿真中最优参数集的SmokeView动画与实验视频的定性对比；其二为同一场仿真过程中GAUGE_HEAT_FLUX变化的动画。 由于MT3模拟数据体量较大，本次仅上传各代最优参数集对应的FDS输入文件。仅针对各逆向建模运行的最优参数集提供完整FDS仿真数据，具体对应关系如下： | 逆向建模运行编号 | 最优复现编号 | | ---- | ---- | | imp_13b | 110751 | | imp_13c | 121106 | | imp_13d | 137738 | | imp_13e | 97493 | | imp_13f | 91988 | | imp_13g | 86988 | | imp_13h | 17480 | | imp_13b_1 | 19033 | | imp_13b_2 | 25043 | | imp_13b_3b | 24149 | | imp_13b_4 | 29666 | | imp_13h_1 | 10685 | | imp_13h_2 | 10024 | | imp_13h_3 | 10109 | | imp_13i | 13253 | 注：本次上传的逆向建模运行命名与论文中使用的标注有所不同，具体对应关系如下： | 逆向建模运行编号 | 论文中标注 | | ---- | ---- | | imp_13b | Tb | | imp_13c | Ta | | imp_13d | Tc | | imp_13e | Ta,b,c | | imp_13f | Tb,c | | imp_13g | Ta,c | | imp_13h | Ta,b,cLA,L1,HC | | imp_13b_1 | TbL1 | | imp_13b_2 | TbPL1 | | imp_13b_3b | TbPL1L1 | | imp_13b_4 | TbPL2,HT | | imp_13h_1 | Ta,b,cPA,L1,HCL1 | | imp_13h_2 | Ta,b,cPA,L1,HCL2 | | imp_13h_3 | Ta,b,cPA,L1,HCL3 | | imp_13i | TbPA,L1,HC | 版本2更新说明：新增预印本内容。 版本3更新说明：新增原稿件被《Fire Safety Journal》拒稿后，在修订过程中生成的新文件。本次修订对应最初投稿至《Fire》期刊的稿件，相关压缩包以"_Revision01"进行标注。