摩托车原厂配套OEM电池TX9-FP循环寿命数据

在规定充放电制度、以及特定的循环次数下，摩托车原厂配套OEM电池的放电容量保持率、容量衰减情况在高倍率启动放电下电压性能以及对应参数的变化率，同时监控高倍率放电下的5秒电压和90秒电压，监控其对应参数的变化率，用于评估该类型电池在长时间循环放电情况下的启动能力，性能衰减情况、电池性能稳定性分析以及电池使用寿命预测。1.数据来源 在规定的循环寿命测试制度下，循环记录摩托车原厂配套OEM电池TX9-FP1000次的实时容量数据 2.数据处理 2.1实时预警 基于摩托车原厂配套OEM电池放电容量，容量保持率和电池高倍率放电得到的5秒电压和30秒电压的性能要求，通过设置监测阀值并实现智能预警，当循环至容量保持率<70%的标称容量时结束循环，或者当高倍率放电的5秒电压低于10V或者90秒电压低于7.2V时结束循环。 当测试结束时，若循环记录1000次中均没有预警，则放电容量取1000次的数据；若循环过程中有预警，则采用预警时的数据作为放电容量。 2.2性能衰减变化率 采用以下公式计算摩托车原厂配套OEM电池性能参数： (1)放电容量保持率=放电容量/标称容量*100%; (2)容量衰减率=（初始容量-终止容量）/初始容量*100%； (3)容量变化率=(终止容量-放电容量)/终止容量； 3.数据应用 通过分析摩托车原厂配套OEM电池的放电容量保持率、容量衰减情况在高倍率启动放电下电压性能以及对应参数的变化率，用于评估该类型电池在长时间循环放电情况下的性能衰减情况、电池性能稳定性分析以及电池使用寿命预测。Under specified charge-discharge regimes and given cycle counts, this dataset collects data on the discharge capacity retention rate, capacity attenuation, voltage performance under high-rate starting discharge and variation rates of corresponding parameters of OEM motorcycle batteries (original equipment manufacturer batteries supplied as standard with motorcycles). It also monitors the 5-second and 90-second voltages during high-rate discharge, as well as the variation rates of their corresponding parameters, to evaluate the starting capability, performance attenuation, battery performance stability and service life prediction of this type of batteries under long-term cyclic discharge conditions. 1. Data Source Real-time capacity data of the OEM motorcycle battery TX9-FP is collected across 1000 cycles under the specified cycle life test regime. 2. Data Processing 2.1 Real-time Early Warning Based on the performance requirements for discharge capacity, discharge capacity retention rate, 5-second voltage and 30-second voltage derived from high-rate discharge of the OEM motorcycle batteries, intelligent early warning is implemented by setting monitoring thresholds. The cycle test will be terminated when the discharge capacity retention rate drops below 70% of the nominal capacity, or when the 5-second voltage under high-rate discharge is lower than 10V, or the 90-second voltage is lower than 7.2V. When the test concludes, if no early warning is triggered during the 1000 cycles, the discharge capacity data from the 1000th cycle is utilized; if early warning occurs during the test, the discharge capacity data recorded at the time of warning is adopted as the final discharge capacity. 2.2 Performance Attenuation Variation Rate The performance parameters of the OEM motorcycle batteries are calculated using the following formulas: (1) Discharge Capacity Retention Rate = (Discharge Capacity / Nominal Capacity) × 100%; (2) Capacity Attenuation Rate = (Initial Capacity - Final Capacity) / Initial Capacity × 100%; (3) Capacity Variation Rate = (Final Capacity - Discharge Capacity) / Final Capacity; 3. Data Application By analyzing the discharge capacity retention rate, capacity attenuation, voltage performance under high-rate starting discharge and variation rates of corresponding parameters of the OEM motorcycle batteries, this dataset is used to evaluate the performance attenuation, battery performance stability and service life prediction of this type of batteries under long-term cyclic discharge conditions.

搜集汇总

数据集介绍

特点

该数据集记录了摩托车原厂配套OEM电池TX9-FP的循环寿命测试数据，包含1027条记录，用于评估电池性能衰减和寿命预测。数据涵盖放电容量、容量保持率等关键参数，并通过算法实现实时预警和性能分析。