Replication Data for: Estimates of the size distribution of meteoric smoke particles from rocket-borne impact probes

Contains raw PCM data streams for the MAXIDUSTY rocket launches, as well as specific files for the MUDD and DUSTY instruments used to produce the resuts in the paper \"Estimates of the size distribution of meteoric smoke particles from rocket-borne impact probes\". Naming and formatting of MATLAB-files (.mat): For MXD-1, MUDD files are separated into .mat files in the format: \"M3G1_straightened\" - Where 'M3' denotes \"MUDD 3\" and 'G1' denotes 'Grid 1'. Grid 2 is denoted by G2, and Bottom plate is denoted by BP. BP currents have additional information about the retarding potential, e.g. \"M2BP_m2\" (MUDD 2, Bottom plate, -2V). Altitudes files are formatted e.g. \"Alt_13_8\" which denotes Altitude, Flight 1 (MXD-1), MUDD 3, Retarding potential 8V. For MXD-1B, The file name formatting is the same, however a 'B' is added in the file name, e.g.: \"Alt_1B3_8\" or \"M2BBP_m2\". The files can be directly loaded into Matlab with the load('')-function. Formatting for tab-separated text files (.txt): There is one file for each respective retarding potential for each respective MUDD-probe. The altitude is given in the same file, i.e. the left column gives payload altitude in meters, and the right column gives MUDD bottom plate potential in nano-Amperes. The naming convention is the same as for the.mat files, such that 'M1BBP_m2.txt' contains the data for MUDD-1 on MXD-1B, for retarding potential -2V (\"m2\"). NB: Note that this is retarding for negative particles, so that a negative potential becomes attractive. For PCM-decoding of the raw telemetry signal, either Andøya Space Center or the responsible author can be contacted for decoding software and telemetry setup format. The .bin-files contains the complete flight-data for both MAXIDUSTY-flights.本数据集包含MAXIDUSTY火箭发射任务的原始脉冲编码调制（PCM）数据流，以及用于生成论文《基于火箭搭载撞击探针的流星烟粒子尺寸分布估算》（Estimates of the size distribution of meteoric smoke particles from rocket-borne impact probes）研究结果的MUDD与DUSTY仪器专用文件。MATLAB文件（.mat）的命名与格式如下：针对MXD-1任务，MUDD仪器的文件被拆分为格式为"M3G1_straightened"的.mat文件——其中"M3"代表"MUDD 3"，"G1"代表"栅格1（Grid 1）"；栅格2记为G2，底板记为BP。底板电流文件包含减速电位的额外信息，例如"M2BP_m2"代表（MUDD 2，底板，-2V）。高度文件的格式例如"Alt_13_8"，代表高度、飞行1（MXD-1）、MUDD 3、减速电位8V。针对MXD-1B任务，文件名格式保持一致，但文件名中新增字符"B"，例如："Alt_1B3_8"或"M2BBP_m2"。此类文件可通过Matlab的load('')函数直接加载。制表符分隔文本文件（.txt）的格式如下：每台MUDD探针对应每种减速电位均配有一个专属文件。文件中同时包含高度信息，即左列为载荷高度（单位：米），右列为MUDD底板电位（单位：纳安）。文件命名规则与.mat文件一致，例如"M1BBP_m2.txt"包含MXD-1B任务中MUDD-1在减速电位-2V（即"m2"）下的相关数据。注意：此处减速电位针对负电性粒子，因此负电位实际表现为吸引特性。如需对原始遥测信号进行PCM解码，可联系安岛航天中心（Andøya Space Center）或通讯作者获取解码软件及遥测配置格式说明。.bin文件包含两次MAXIDUSTY任务的完整飞行数据。