BPA RUP ground plane

This data is kept daily and is therefore always up to date Summary: The plans for construction are defined in the Urban Planning Act (Decree on Spatial Planning, coordinated on 22 October 1996); the regional plan, the general plan of construction (A.P.A.) and the special plan of construction (B.P.A.). A special plan of construction shall indicate, for the part of the municipal territory concerned: the existing situation; the detailed destination of different parts of the territory for habitation, industry, agriculture or any other use; the route of any changes to be made to the existing road network; rules on the location, size and prosperity of buildings and fences, as well as rules on courtyards and gardens. It may also indicate: rules on the construction and equipping of roads, strips free of construction and planting; places intended for the construction of green spaces, forest reserves, sports fields and cemeteries, as well as public buildings and monuments; if a land consolidation or reparcelling proves necessary, the boundaries of the new plots, stating that those boundaries may be changed by the aldermen's council with the approval of the Flemish Government. The regulations listed above may include property restrictions, including building bans. Where a regional, regional or general plan exists, the special plan shall conform to and supplement its instructions and provisions. It can deviate from it if necessary. Sinds het nieuw decreet op de ruimtelijke ordening van 18 mei 1999 (DRO) wordt het vroegere systeem van gewestplanwijzigingen en BPA's vervangen door de meer flexibele Ruimtelijke UitvoeringsPlannen (RUP's), Deze worden opgemaakt door de 3 bevoegdheisniveau's nl, gemeente, provincie en gewest op basis van het subsidiariteitsprincipe, Deze plannen worden opgemaakt om uitvoering te geven aan de ruimtelijke structuurplannen en worden bijgevolg steeds opgemaakt vertrekkende vanuit de visie van een ruimtelijk structuurplan, Deze laatste zijn strategische beleidsplannen die voor een bepaalde plantermijn aangeven hoe de ruimte van het betrokken grondgebied ontwikkeld en beheerd zal worden, Een RUP bevat elementen van bestemming, beheer en inrichting, Deze informatie zit vervat in stedenbouwkundige voorschriften die van toepassing zijn op een stuk grondgebied en bijgevolg en ruimtelijke link hebben (al dan niet perceelsgebonden) De hier gepubliceerde laag 'BPA-RUP-grondvlak (actuele toestand)' is een digitale vectoriële versie van de samengevoegde geactualiseerde BPA's en RUP's voor Antwerpen en wordt best gebruikt in combinatie met de gegeorefereerde scans van de originele analoge (papieren) plannen. The layer is part of a more extensive file composed of 9 layers, namely the BPA-RUP substrates, the overprints (in 2 layers based on whether or not geometrically accurate), the lines (in 2 layers based on whether or not geometrically accurate), the points (in 2 layers based on whether or not geometrically accurate), a layer for the possible sub-zones within the RUP and the BPA or RUP contour (part of the planning register) . Here, only the updated destination areas (the so-called 'ground colour' e.g., 'office zone') of the legally valid BPAs and RUPs are displayed and documented. This layer is by definition non-overlapping within the same BPA or RUP, (unlike the overprint layer which can contain overlapping parts). Structure lay according to directive on http://www2.vlaanderen.be/spatial/registers/digirups/digirups.html. For the municipal RUPs of Antwerp, the main destination is chosen from the list in the RUPs manual. (Coloring is also based on this) Purpose: The destination contours serve to support spatial planning and advice in Antwerp at all policy levels. It is an important information layer in the preparation, implementation and evaluation of the policy through spatial analysis, kartography, and automated file handling. Creation: Digitisation of the BPA destinations of the legally valid BPAs on the basis of scanned and georeferenced scans.Recent BPAs and Municipal RUPs are supplied in GIS format, The provincial and regional RUPs are required by decree in GIS supplied by the relevant government.本数据每日更新，因此始终保持最新状态。 摘要：建筑规划相关要求在《城市规划法》（1996年10月22日协调通过的《空间规划法令》）中予以明确，涵盖区域规划、总建筑规划（A.P.A.）以及专项建筑规划（B.P.A.）。 专项建筑规划需针对所辖市政管辖范围，明确以下内容：现有场地状况；辖区内不同地块的详细用途，包括居住、工业、农业或其他用途；现有道路网络的改造路线；建筑与围栏的选址、规模及相关要求，以及庭院与花园的相关规则。 此外，专项建筑规划还可涵盖以下内容：道路建设与配套设施、建筑禁建带及绿化种植相关规则；预留用于建设绿地、森林保护区、运动场、公墓，以及公共建筑与纪念性设施的地块；若需开展土地整合或地块重划，则需明确新地块的边界，并说明该边界可由市议员委员会经佛兰芒政府（Flemish Government）批准后进行调整。 上述相关规则可包含产权限制条款，包括建筑禁令。若已存在区域规划、跨区域规划或总建筑规划，则专项建筑规划需符合并补充其相关指示与规定，必要时可与之存在偏差。 自1999年5月18日颁布的新空间规划法令（DRO）实施以来，原有的区域规划修改与专项建筑规划（B.P.A.）体系被更为灵活的空间实施规划（Ruimtelijke UitvoeringsPlannen，简称RUPs）所取代。该规划由三个权责层级制定，即市政、省级与区域层级，遵循辅助性原则。制定此类规划旨在落实空间结构规划，因此始终以空间结构规划的愿景为出发点。空间结构规划属于战略性政策规划，明确了特定规划周期内相关辖区空间的开发与管理方式。 空间实施规划（RUPs）包含用途指定、管理与整治相关要素，此类信息载于适用于特定辖区地块的城市规划法规中，因此与空间规划存在关联（可与地块绑定，亦可无关）。 本次发布的“BPA-RUP地块（现状）”图层，是安特卫普市所有已更新合并的合法专项建筑规划（B.P.A.）与空间实施规划（RUPs）的数字化矢量版本，建议结合原始纸质规划的地理参照扫描件使用。 该图层属于包含9个图层的更大型数据集的一部分，具体包括：BPA-RUP基底图层、套印图层（分为2个图层，依据几何精度区分）、线条图层（分为2个图层，依据几何精度区分）、点图层（分为2个图层，依据几何精度区分）、空间实施规划（RUPs）与专项建筑规划（B.P.A.）内可能存在的子区域图层，以及规划登记册中的规划轮廓图层。 本图层仅展示并记录合法有效的专项建筑规划（B.P.A.）与空间实施规划（RUPs）中已更新的用途分区（即所谓的“用地底色”，例如“办公区”）。根据定义，同一专项建筑规划或空间实施规划内的本图层地块互不重叠（与可包含重叠区域的套印图层不同）。图层结构遵循http://www2.vlaanderen.be/spatial/registers/digirups/digirups.html中规定的指令。 对于安特卫普市的空间实施规划（RUPs），其主要用途类型选自空间实施规划手册中的列表（配色方案亦基于此列表制定）。 应用场景：用途分区轮廓可用于支撑安特卫普市各级政策制定中的空间规划与咨询工作。该图层是通过空间分析、地图制图与自动化文件处理进行政策制定、实施与评估的重要信息层。 数据制作：基于经扫描并完成地理参照的图像，对合法有效专项建筑规划（B.P.A.）的用途分区进行数字化处理。最新的专项建筑规划（B.P.A.）与市级空间实施规划（RUPs）以GIS（地理信息系统）格式提供，省级与区域级空间实施规划（RUPs）则由相关政府部门依据法令要求以GIS格式提交。