Dataset on Integrated Solid Desiccant Packed Bed - Oscillating Heat Pipe Systems

This experimental dataset for Integrated Solid Desiccant Packed Bed-Oscillating Heat Pipe System contains raw temperature data obtained from Fully Packed Bed (FPB), Small Annulus Packed Bed (SAPB), Medium Annulus Packed Bed (MAPB) and Large Annulus Packed Bed (LAPB) all respectively integrated with Helically Coiled Oscillating Heat Pipes (HCOHPs) charged respectively with Ethanol (EOHP), Methanol (MOHP), and Deionized Water (WOHP). The packed beds were filled with silica gel (Silicon Dioxide/SiO2) of particle size between 3.35mm-4.75mm. The annulus packed beds were in Heggs et al (1994) Z configurations described by their annular dimensions as small (SAPB), medium (MAPB) and large (LAPB) corresponding to diametrical ratios (Do/Di) of 2, 2.35 and 3.08, respectively.
The data are mainly raw temperature data from Omega K-type thermocouples inserted in three designated Mass Transfer Zones (MTZ 1, MTZ 2 and MTZ 3), corresponding Walls (Wall 1, Wall 2, and Wall 3), Evaporators (Evap), Condensers (Cond), and Adiabatic Sections (Adiab) of each HCOHP integrated with a packed bed. Each packed bed was integrated with three (3) HCOHPs containing the same working fluid. Each HCOHP had two (2) thermocouples on their adiabatic sections and three (3) thermocouples installed on their evaporators and condensers respectively. The HCOHPs were numbered 1, 2 and 3 and the position of thermocouples on each component were labelled a, b, and c. For instance, the first evaporator would be labelled Evap_1 and where the thermocouple is located can be identified by say Evap_1a indicating the thermocouple is on the first position on the 1st evaporator. The ambient temperature data are also presented for each integrated system. The inlet and outlet pressures of each packed bed obtained as electrical pulses in Voltage and converted into Pascal (Pa) are captioned as Derived Pressure in Pa. Inlet and outlet air temperature, velocity and relative humidity obtained from Sentry ST732 Hotwire Anemometers and AZ 8829 Temperature and RH% data loggers are on the Inlet and Outlet Data Tabs. The dataset has seven (7) spreadsheets each for a packed bed configuration type integrated with the EOHP, MOHP or WOHP. For instance, for SAPB integrated with the HCOHPs i.e., EOHP, MOHP, and WOHP respectively, the combinations are SAPB-EOHP, SAPB-MOHP and SAPB-WOHP respectively. Each combination is presented on separate Tabs on the spreadsheet with its test run number such as SAPB-EOHP 1, SAPB-MOHP 1 and SAPB-WOHP 1 for test run 1 and SAPB-EOHP 2, SAPB-MOHP 2 and SAPB-WOHP 2 respectively for test run 2. The annulus packed bed configurations integrated with the HCOHPs have data for two test runs presented. Only one test run data is presented for the fully packed bed (FPB) namely FPB-EOHP, FPB-MOHP and FPB-WOHP respectively with respective inlet and outlet conditions data.

本实验数据集针对集成式固体干燥剂填充床-振荡热管系统，包含从全填充床（FPB）、小环形填充床（SAPB）、中环形填充床（MAPB）和大型环形填充床（LAPB）中分别集成的螺旋盘管振荡热管（HCOHPs）获取的原始温度数据，这些热管分别充填有乙醇（EOHP）、甲醇（MOHP）和去离子水（WOHP）。填充床填充有粒径介于3.35mm至4.75mm之间的硅胶（二氧化硅/SiO2）。环形填充床采用Heggs等人（1994年）所描述的Z型配置，其环形尺寸分别为小（SAPB）、中（MAPB）和大型（LAPB），对应的直径比（Do/Di）分别为2、2.35和3.08。数据主要来源于插入于三个指定质量传递区（MTZ 1、MTZ 2和MTZ 3）、对应墙壁（Wall 1、Wall 2和Wall 3）、蒸发器（Evap）、冷凝器（Cond）和绝热段（Adiab）的Omega K型热电偶获取的原始温度数据。每个填充床与包含相同工作流体的三个（3）HCOHPs集成。每个HCOHP在其绝热段配备两个（2）热电偶，并在蒸发器和冷凝器上分别安装三个（3）热电偶。HCOHPs编号为1、2和3，每个组件上热电偶的位置标记为a、b和c。例如，第一个蒸发器标记为Evap_1，热电偶所在位置可通过如Evap_1a来识别，表示热电偶位于第一个蒸发器的第一个位置。每个集成系统的环境温度数据也一并呈现。每个填充床的进口和出口压力以电压脉冲形式获得，并转换为帕斯卡（Pa），标注为“派生压力（Pa）”。进口和出口空气温度、速度和相对湿度由Sentry ST732热线风速仪和AZ 8829温度及相对湿度数据记录仪获得，并位于“进口和出口数据标签”上。数据集包含七个（7）电子表格，分别对应集成有EOHP、MOHP或WOHP的填充床配置类型。例如，对于集成有HCOHPs的SAPB，即EOHP、MOHP和WOHP的配置，分别为SAPB-EOHP、SAPB-MOHP和SAPB-WOHP。每个组合在电子表格的单独标签上呈现，并带有其测试运行编号，如SAPB-EOHP 1、SAPB-MOHP 1和SAPB-WOHP 1对应测试运行1，以及SAPB-EOHP 2、SAPB-MOHP 2和SAPB-WOHP 2分别对应测试运行2。环形填充床配置与HCOHPs集成时，呈现两个测试运行的数据。对于全填充床（FPB），仅呈现一个测试运行的数据，即FPB-EOHP、FPB-MOHP和FPB-WOHP，分别带有各自的进口和出口条件数据。