CCS - CCS2 Mooring data November 2019 deployment

Project Overview: A range of solutions will be required to reach globally agreed emissions reductions targets for carbon dioxide (CO2). Carbon capture and storage (CCS) is part of the suite of technologies that will contribute to lowering atmospheric emissions of CO2 from Australia's energy system. There are a wide variety of technologies at various stages of technical and commercial readiness, with more development underway for cost effective CO2 capture and storage. Our research will provide new knowledge to inform cost-efficient measurement, monitoring and verification (MMV) of the environment of CCS projects in coastal waters.--o--Description:Measurements are made Seabird Seaphox (for dissolved oxygen, pH, Seawater Temperature and Salinity), mounted on a lander. The Seaphox takes a reading every hour in the UTC hour and is transmitted real time through acoustic and/or 3G modems. The Seaphox consists of a SeaFET (pH) and SBE-37-SMP-ODO CTD (SW temperature, Salinity and Dissolved Oxygen [SBE63]).Relevant component details: make, model, serial number, firmware version, settings:Sensor | Make | Model | Serial Number | CalibrationpH, DO,T and S sensor | Seabird Seaphox | SeaFET | 1031 |2019-04, factory calibratedpH, DO,T and S sensor | Seabird Seaphox | SBE-37-SMP-ODO | 15559 | 2019-04, factory calibratedpH, DO,T and S sensor | Seabird Seaphox | SBE-63 | 1689 | 2019-04, factory calibratedCalibration Information (if applicable)SBE 37 (T, S, DO) and the SeaFET (pH) are calibrated by the factory and verified in the CSIRO laboratory. The pH reported in the files is flagged questionable for the pre-deployment calibrated data due to possible calibration changes which can occur after deployment pH (calibrated) is further processed after the recovery using in situ bottle sample where available, using Total Alkalinity (TA) and Dissolved Inorganic Carbon (DIC), which will be converted to pH using CO2SYS, where the Lueker k1k2 dissociation constant is used. Location: 38.2588333S 147.4220333E项目概述：为达成全球共识的二氧化碳（CO2）减排目标，需配套多种解决方案。碳捕获与封存（CCS）是可助力降低澳大利亚能源系统向大气排放CO2的技术组合之一。当前已有多款处于不同技术与商业化成熟度阶段的相关技术，且针对低成本高效的CO2捕获与封存技术的研发工作正持续推进。本研究将提供全新的知识支撑，为近岸海域CCS项目的环境成本效益型测量、监测与核查（MMV）工作提供决策参考。 --o-- 描述： 本次检测由搭载于着陆器的海鸟（Seabird）Seaphox传感器完成，该传感器可采集溶解氧、pH值、海水温度与盐度数据。Seaphox传感器于每个UTC整点采集一次数据，并通过声学调制解调器和/或3G调制解调器实时传输数据。该传感器由SeaFET（用于pH检测）与SBE-37-SMP-ODO CTD（用于海水温度、盐度与溶解氧检测，对应型号SBE63）组成。 相关组件详情：品牌、型号、序列号、固件版本与配置参数： | 传感器类型 | 品牌/设备 | 型号 | 序列号 | 校准信息 | |--------------------------|-------------------------|---------------------|--------|------------------------| | pH、溶解氧、温度与盐度传感器 | 海鸟（Seabird）Seaphox | SeaFET | 1031 | 2019年4月，工厂校准 | | pH、溶解氧、温度与盐度传感器 | 海鸟（Seabird）Seaphox | SBE-37-SMP-ODO | 15559 | 2019年4月，工厂校准 | | pH、溶解氧、温度与盐度传感器 | 海鸟（Seabird）Seaphox | SBE-63 | 1689 | 2019年4月，工厂校准 | 校准信息（如适用）： SBE 37（用于温度、盐度与溶解氧检测）与SeaFET（用于pH检测）均由原厂校准，并在澳大利亚联邦科学与工业研究组织（CSIRO）实验室完成验证。部署前校准数据对应的文件中记录的pH值被标记为可疑，原因是设备部署后可能发生校准偏移。经校准的pH值将在回收后，若有可用的原位瓶装水样，将结合总碱度（TA）与溶解无机碳（DIC）进行进一步处理；相关数据将通过CO2SYS工具转换为pH值，转换过程采用Lueker k1k2解离常数。 监测点位：南纬38.2588333度，东经147.4220333度