Data and morphometric results from a physical experiment simulating washover deposition

This portfolio includes two sets of data, used and explained in Lazarus, Williams &amp; Goldstein (preprint: https://doi.org/10.31223/X5JH1X): washover morphometry measured from a physical experiment to simulate washover deposition, conducted at the Total Environment Simulator (TES) at the University of Hull ('TES_washover_morphometry.csv'); the terrestrial laser-scan data in which those morphometric characteristics of washover were measured ('Run01.zip' – 'Run22.zip'), with a table of experimental conditions for each trial (run). <strong>Washover morphometry dataset</strong> <em><strong>TES_washover_morphometry.csv</strong></em> – Washover morphometry from the 22 experimental trials in the TES at Hull. Dataset includes: deposit ID, throat width (m), deposit width (m), intrusion length (m), deposit area (m²), deposit volume (m³), deposit perimeter (m), built fraction, forcing mode ("inundation" or "wave-driven"), and a dataset label ("TES"). <strong>Table of experimental conditions</strong> <em><strong>TES_washover_trials.pdf</strong></em> – Table of experimental conditions for each trial (run). <strong>Data folders</strong> These folders contain terrestrial laser-scan data from washover experiments at the Total Environment Simulator (TES) at the University of Hull. These files were used to identify and measure the individual washover deposits in each experimental trial. Each folder (Run01–Run22) contains data (in 'e57' file format) for a specific trial, and includes the following: <em><strong>RunX_DOD.e57</strong></em> – This is a point cloud of the difference between the Pre_Processed and Post_Processed files. This is produced by subtracting the 'post' values from the 'pre' values. <em><strong>RunX_Post_Processed.e57</strong></em> – This is a point cloud of the topography at the end of the experimental run, created from the raw data file by trimming out extraneous points. <em><strong>RunX_Post_Raw.e57</strong></em> – This is a point cloud of the topography at the end of the experimental run, created in FARO Scene to merge two individual point clouds (covering the entire interior of the TES) into a non-proprietary file format. <em><strong>RunX_Pre_Processed.e57</strong></em> – This is a point cloud of the topography prior to the experimental run, created from the raw data file by trimming out extraneous points. <em><strong>RunX_Pre_Raw.e57</strong></em> – This is a point cloud of the topography prior to the experimental run, created in FARO Scene to merge two individual point clouds (covering the entire interior of the TES) into a non-proprietary file format.本数据集包含两组数据，相关内容已在拉扎勒斯（Lazarus）、威廉姆斯（Williams）与戈德斯坦（Goldstein）的预印本（预印本链接：https://doi.org/10.31223/X5JH1X）中进行了详细阐述与说明： 第一组为基于物理实验测得的冲溢地貌形态学（washover morphometry）数据，该实验在赫尔大学（University of Hull）的全环境模拟器（Total Environment Simulator, TES）中开展，用于模拟冲溢沉积过程，对应数据文件为`TES_washover_morphometry.csv`； 第二组为用于测量上述冲溢地貌形态特征的地面激光扫描（terrestrial laser-scan）数据（对应压缩包为`Run01.zip`至`Run22.zip`），以及各试验（运行批次）的试验条件表。 **冲溢地貌形态学数据集** ***`TES_washover_morphometry.csv`***——来自赫尔大学TES平台22组试验的冲溢地貌形态学数据。数据集包含以下字段：沉积ID、喉道宽度（m）、沉积体宽度（m）、侵入长度（m）、沉积面积（m²）、沉积体积（m³）、沉积周长（m）、建造占比、强迫模式（“淹没”或“波浪驱动”），以及数据集标签“TES”。 **试验条件表** ***`TES_washover_trials.pdf`***——各试验（运行批次）的试验条件明细表。 **数据文件夹** 这些文件夹包含赫尔大学TES平台冲溢实验的地面激光扫描数据，用于识别并测量各试验中单个冲溢沉积体。每个文件夹（Run01至Run22）对应特定试验，均采用`e57`文件格式存储数据，包含以下文件： ***`RunX_DOD.e57`***——预处理前与预处理后的地形点云（point cloud）差值云图，通过将“预处理后”数值减去“预处理前”数值生成。 ***`RunX_Post_Processed.e57`***——试验结束时的地形点云数据，通过修剪原始数据中的冗余点生成。 ***`RunX_Post_Raw.e57`***——试验结束时的地形点云数据，通过FARO Scene软件将两组覆盖TES全内部空间的单点云合并为非专有格式文件生成。 ***`RunX_Pre_Processed.e57`***——试验开始前的地形点云数据，通过修剪原始数据中的冗余点生成。 ***`RunX_Pre_Raw.e57`***——试验开始前的地形点云数据，通过FARO Scene软件将两组覆盖TES全内部空间的单点云合并为非专有格式文件生成。