Recorded temperature data of a reinforced concrete, 1.2-m long, beam-slab model and associated meteorological data.

The data contain internal and surface temperature measurements of a 1.2 m-long, reinforced concrete girder-slab element exposed to the environmental conditions of the city of Bucaramanga, Colombia (Coordinates: 7°08'35", 73°07'18"). In addition, meteorological variables of the environment near the element were recorded. The data was measured from July 7, 2023, to November 6, 2023. The data were obtained by: Internal Temperature (file name: InternalTemperature): 40 thermocouples were embedded in the element (Fig. 1) to collect data every 30 minutes from 6:30 AM on July 10, 2023 to 11:30 PM on November 6, 2023. Temperatures are in degrees Celsius (°C). Surface Temperature (file name: SurfaceTemperatureCameraEast and SurfaceTemperatureCameraWest): A FLIR E6 XT thermal camera was used to record Surface temperature of 10 points on the EAST (Fig. 2) and WEST (Fig. 3) faces of the element from 6:30 AM on June 29, 2023 to 4 PM on October 31, 2023. Twenty daily measurements were recorded every 30 minutes. Temperatures are in degrees Celsius (°C). Surface Temperature (file name: SurfaceTemperatureDroneEast): A DJI MAVIC 2 ENTERPRISE ADVANCED (EU) drone equipped with a thermal imaging camera measured the surface temperature of 10 points on the EAST side of the element (Fig. 4) every 30 minutes, from 6:30 AM on September 9 to 4 PM on October 31. Temperatures are in degrees Celsius (°C). Meteorological variables (file name: WeatherStationData): A DAVIS VANTAGE PRO-2 WLRS weather station recorded data every 30 minutes from 12 AM on July 10, 2023, to 12:30 PM on November 6, 2023. The data included the average, maximum, and minimum ambient temperature (°C); relative humidity (%); speed (m/s) and wind direction (cardinal direction); atmospheric pressure (mb); precipitation (mm) and average and maximum solar radiation (W/m2).本数据集包含置于哥伦比亚布卡拉曼加市（坐标：7°08'35″，73°07'18″）自然环境中的1.2米长钢筋混凝土梁板构件的内部与表面温度实测数据，同时记录了该构件周边的环境气象变量。所有数据的采集时段为2023年7月7日至2023年11月6日。 内部温度（文件命名：InternalTemperature）：在构件内部嵌入40支热电偶（图1），采集时段为2023年7月10日6:30至2023年11月6日23:30，采样间隔为30分钟。温度单位为摄氏度（℃）。 表面温度（文件命名：SurfaceTemperatureCameraEast 与 SurfaceTemperatureCameraWest）：采用FLIR E6 XT热成像相机，分别采集构件东侧（图2）、西侧（图3）共10个测点的表面温度，采集时段为2023年6月29日6:30至2023年10月31日16:00，每日开展20次测量，采样间隔为30分钟。温度单位为摄氏度（℃）。 表面温度（文件命名：SurfaceTemperatureDroneEast）：搭载热成像相机的DJI MAVIC 2 ENTERPRISE ADVANCED（EU）无人机，于2023年9月9日6:30至2023年10月31日16:00期间，每30分钟采集1次构件东侧10个测点的表面温度。温度单位为摄氏度（℃）。 气象变量（文件命名：WeatherStationData）：采用DAVIS VANTAGE PRO-2 WLRS气象站，采集时段为2023年7月10日00:00至2023年11月6日12:30，采样间隔为30分钟。采集的气象参数包括：环境平均、最高与最低气温（℃）；相对湿度（%）；风速（m/s）与风向（方位基点）；大气压强（mb）；降水量（mm），以及太阳辐射平均强度与最大强度（W/m²）。