Laser altimeter data obtained over sea-ice during the SIZONet campaign in Apr, 2008; profile SIZONet2008_SBLA_20080412T2311_71.60_-156.62_thr06_data_Vers5@en

Sea ice surface roughness data were obtained during the SIZONet campaign in Apr, 2008 with a Single Beam Laser Altimeter (SBLA) mounted inside an electromagnetic system (EM-Bird) towed at 10-30 m height above surface by a Helicopter (Unknown model). A method developed by Hibler (1972) was used to a) isolate the surface profile from low-frequency variations associated with the aircraft motion and b) to identify pressure ridge sails. The processing steps are described in https://epic.awi.de/id/eprint/56364/. We applied a ridge detection threshold of 0.6 m, which means that only sails higher 0.6 m are detected. Version and name of the processing routine: Laser_Altimeter_Processing_VS5_06_20.py (vers.5, Feb 22, 2024, https://gitlab.awi.de/sitem/sbla_processing.git). SBLA records (RIEGL - LD90) are provided at a sampling rate of 100 Hz. Sensor accuracy is 5 cm with a beam diameter at surface of 5.8 cm. This specific dataset was obtained on 20080412T2311. It includes recorded altimeter readings, the derived surface elevation and width/height/spacing of detected pressure ridge sails. Note on data quality: 5.8 cm . File name: [DMS/PANGAEA Campaing Identifier] + [DEVICE] + [DATE/TIME] + [LAT/LON] + [Detection Threshold] + [Object] + [Version] + [Format]本数据集的海冰表面粗糙度数据采集于2008年4月的SIZONet科考航次，由搭载于电磁系统（EM-Bird）内的单波束激光高度计（Single Beam Laser Altimeter, SBLA）完成采集，该系统由未知型号直升机以距海面10~30米的高度拖曳作业。 研究采用希勒（Hibler）1972年提出的方法完成两项核心处理任务：a）从信号中剥离与飞行器运动相关的低频扰动，得到纯净的海冰表面剖面；b）识别冰脊帆。具体处理流程详见https://epic.awi.de/id/eprint/56364/。 本次处理设置的冰脊检测阈值为0.6米，即仅可识别高度不低于0.6米的冰脊帆。处理程序的版本与名称为：Laser_Altimeter_Processing_VS5_06_20.py（版本5，2024年2月22日，https://gitlab.awi.de/sitem/sbla_processing.git）。 本数据集所用的单波束激光高度计型号为RIEGL LD90，采样率为100赫兹，传感器精度为5厘米，地表激光光斑直径为5.8厘米。 本数据集的采集时间为2008年4月12日23时11分（格式标识：20080412T2311），包含记录的高度计原始读数、反演得到的表面高程数据，以及已识别的冰脊帆的宽度、高度与间距信息。 数据质量备注：激光光斑直径为5.8厘米。 文件名命名规则为：[DMS/PANGAEA科考航次标识符] + [设备标识] + [日期/时间] + [纬度/经度] + [检测阈值] + [目标对象] + [版本号] + [文件格式]