液压乘客电梯监督检验收费计算数据

液压乘客电梯监督检验收费计算是根据电梯的具体情况，包括电梯的额定载重量、额定速度、层/站/门数等因素，来确定检验费用的金额。它能够为电梯使用单位提供合理的收费依据，为电梯检验机构提供方便准确的收费标准。1、数据采集：收集液压乘客电梯额定载重量、额定速度、电梯层/站/门数、检验种类等参数。2、数据处理：首先根据额定速度v≤1，vx=0；1＜v≤1.75，vx=0.1；1.75＜v≤2.5，vx=0.15；v＞2.5,vx=2确定额定速度系数。根据额定载重量t≤1000，tx=0;1000＜t≤2000，tx=0.1;t＞2000，tx=0.15确定额定载重量系数。检验种类系数，安装监检为2，改造监检和大修监检为1.5。是否进口系数，是为1.5，否为1。3、套用算法公式计算：液压乘客电梯监督检验收费实收金额=（收费标准*（1+额定载重量系数+额定速度系数）+（【层/站/门三个参数中的最大值】-5）*80）*检验种类*其他情况*是否进口，其中，【层/站/门三个参数中的最大值】如果三个参数最大值小于5则按5算。其他情况是指如同时是防爆电梯，需乘系数1.5，如同时是汽车电梯，需乘系数1.2，如其他情况无，则系数为1。The supervision and inspection fee calculation for hydraulic passenger elevators determines the total inspection fee based on the elevator's specific characteristics, including factors such as rated load capacity, rated speed, number of floors, stations and doors, etc. It provides a reasonable charging basis for elevator user units and offers convenient and accurate charging standards for elevator inspection institutions. 1. Data Collection: Collect parameters including the rated load capacity, rated speed, number of elevator floors, stations and doors, and inspection type of hydraulic passenger elevators. 2. Data Processing: First, determine the rated speed coefficient (vₓ) according to the following criteria: - When v ≤ 1, vₓ = 0; - When 1 < v ≤ 1.75, vₓ = 0.1; - When 1.75 < v ≤ 2.5, vₓ = 0.15; - When v > 2.5, vₓ = 2. Then determine the rated load coefficient (tₓ) based on the following rules: - When t ≤ 1000, tₓ = 0; - When 1000 < t ≤ 2000, tₓ = 0.1; - When t > 2000, tₓ = 0.15. For the inspection type coefficient: 2 for supervision inspection during installation, 1.5 for supervision inspection during modification and major overhaul. For the import coefficient: 1.5 for imported elevators, and 1 for domestic elevators. 3. Algorithm Application and Fee Calculation: The actual collected supervision and inspection fee for hydraulic passenger elevators is calculated as: Actual Fee = (Charging Standard * (1 + Rated Load Coefficient + Rated Speed Coefficient) + (max(Floors, Stations, Doors) - 5) * 80) * Inspection Type Coefficient * Other Situation Coefficient * Import Coefficient Note: If the maximum value among the three parameters (floors, stations and doors) is less than 5, it shall be calculated as 5. The "Other Situation Coefficient" is defined as: 1.5 for explosion-proof elevators, 1.2 for automobile elevators, and 1 for all other unmentioned scenarios.